conductive polymer aluminum solid electrolytic capacitors lf series specifications characteristics of temperature impedance ratio category temperature range rated voltage range rated capacitance range capacitance tolerance tan esr (1) leakage current ( 2) performance characteristics item 55 ~ +105? 2.5 ~ 16v 270 ~ 1000 f 20% at 120hz, 20? not more than value of standard ratings at 120hz, 20? not more than value of standard ratings at 100khz, 20? not more than value of standard ratings. after 2 minute's application of rated voltage. 20? z+105? / z+20? 1.25 (100khz) z 55? / z+20? 1.25 endurance damp heat resistance to soldering heat marking after 2000 hours' application of rated voltage at 105?, capacitors meet the specified value for life characteristics listed at right. after 1000 hours' application of rated voltage at 60? 90%rh, capacitors meet the specified value for life characteristics listed at right. to comply with recommended conditions for reflow soldering. pre-heating shall be done at 150 ~ 200? and for 60 ~ 180 sec. peak temp. is 265?, within 10 sec. measurement for solder temperature profile shall be made at a point on the terminal nearest where the terminals protrude through the soldering side of pc board. navy blue print on the case top capacitance change tan leakage current ( 2) esr (1) within 20% of initial value ( 3 ) 150% or less of the initial specified value 150% or less of the initial specified value initial specified value or less capacitance change tan leakage current ( 2) esr (1) within 20% of initial value ( 3 ) 150% or less of the initial specified value 150% or less of the initial specified value initial specified value or less capacitance change tan leakage current ( 2) esr (1) within 10% of initial value ( 3) 130% or less of the initial specified value 130% or less of the initial specified value initial specified value or less ultra low esr, high ripple current. load life of 2000 hours at 105?. radial lead type : lead free flow soldering condition correspondence. adapted to the rohs directive (2002/95/ec). 1 esr measurements should be made at a point on the terminal nearest the end seal of the capacitor. 2 conditioning : if there is doubt about the measured result, measurement should be made again after the rated voltage is appl ied for 120 minutes at the temperature of 105?. 3 initial value : the value before test of examination of resistance to soldering. taping code l +0.5max. 15min 4min d +0.5 max. laminated case silvered lead wire d lf 560 g 6x1 capacitance series lot. no. voltage(g:4v) p 0.5 dimensions type numbering system (example : 4v 560 f) voltage v 2.5 4 6.3 10 16 code e g j a c size d l p d 8 9l 8.0 8.5 3.5 0.6 8 12l 8.0 11.5 3.5 0.6 10 13l 10.0 12.5 5.0 0.6 (mm) radial lead type, standard dimension table in next page. please refer to page 21 about the end seal configulation. cat.8100v
conductive polymer aluminum solid electrolytic capacitors lf series standard ratings 2.5 (0e) 4 (0g) 6.3 (0j) 10 (1a) 16 (1c) rated capacitance (f) case size d l (mm) tan leakage current (0.2cv)(a) esr (m ? ) (at 100khz 20 ? c) rated ripple (marms) rated voltage ( v ) ( code ) 560 680 820 820 1000 560 560 680 820 470 470 680 270 470 270 470 part number plf0e561mco1 plf0e681mdo1 plf0e821mco6 plf0e821mdo1 plf0e102mdo1 plf0g561mco6 plf0g561mdo1 plf0g681mdo1 plf0g821mdo1 PLF0J471MCO6 plf0j471mdo1 plf0j681mdo1 plf1a271mdo1 plf1a471mdo1 plf1c271mdo1 plf1c471mdo1 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 280 340 410 410 500 448 448 544 656 592 592 857 540 940 864 1504 6 6 7 6 6 7 7 6 6 7 7 6 8 7 9 9 4800 5700 5200 6200 6500 5200 5500 6200 6500 5200 5500 6300 4900 5700 4800 5000 8 9 8 12 8 9 8 12 10 13 8 9 8 12 8 12 10 13 8 9 8 12 10 13 8 12 10 13 8 12 10 13 no marked, will be put at 12th digit of type numbering system. : in this case, will be put at 12th digit of type numbering system. 6 1 taping specifications are given in page 24. please refer to page 3 for the minimum order quantity. rated ripple (marms) at 105 c 100khz cat.8100v
|
